Synthesis of MgAl2O4 Spinel Nanometer Powder via Biology Polysaccharide Assisted Sol-Gel Process

A novel and cost-effective sol-gel process for preparation of MgAl₂O₄ spinel nanometer powders has been developed in this study. A solution of magnesium and aluminum nitrates in stoichiometric proportion was successfully embraced in the biology polysaccharide gel network, formed by the synergistic interaction between xanthan gum (XG) and locust bean gum (LBG) utilizing their broad-spectrum stability of salt tolerance and character of transformation from sol to gel on the condition of proper temperature and relative proportion of polymeric components. Dry gel could be obtained by vacuum dehydration of aqueous gel at low temperatures. Monolithic MgAl₂O₄ spinel nanometer powders were produced by calcining the dry gel above 800°C, with average crystallite size of 20 nanometers.     

Al掺杂对尖晶石型LiMn2O4结构及循环性能的影响

用柠檬酸作为螯和物的载体,采用溶胶-凝胶法合成了A l3 掺杂的锂离子电池正极材料L iA lxMn2-xO4。XRD,SEM研究表明,于800℃煅烧可获得单一尖晶石结构的物相;随着A l3 掺入量的增加,L iA lxMn2-xO4的晶格常数变小,晶格更趋于完整,有利于抑制因锂的反复脱嵌而造成的结构破坏。x=0.05时,首次放电容量为103.8 mAh.g-1,25次循环后放电容量还有100.6 mAh.g-1,容量衰减仅为3.08%。     

尖晶石锂锰氧化物锂离子嵌脱过程的交流阻抗谱研究

用粉末微电极研究了尖晶石锂锰氧化物在不同嵌锂状态下嵌脱锂过程的交流阻 抗图谱，提出了新的等效电路模型。描述锂离子在固体中扩散的Warburg阻抗与累 积或消耗的嵌入电容在Lix MnO4中的x≤0．5时串联，0．5＜x≤1时并联。用提出 的等效电路模型分阶段拟合了实验所得的交流阻抗谱，拟合值与实验值相当吻合， 由拟合结果得到不同电位下锂离子在表面膜中的迁移电阻和电容，界面电荷传递电 阻，双层电容，锂离子在固体中扩散系数和累积或消耗的嵌入电容。     

SnO2-Nb2O5/MgAl2O4/α-Al2O3催化环氧乙烷水合制乙二醇

采用水热稳定的MgAl2O4尖晶石对-αAl2O3载体表面进行修饰,采用具有较强亲水性能的SnO2对活性组分Nb2O5进行修饰,制备了SnO2-Nb2O5/MgAl2O4/-αAl2O3催化剂,并用于环氧乙烷水合制乙二醇反应.采用X射线衍射、红外光谱和程序升温脱附研究了Sn/Nb摩尔比对催化剂酸性、环氧乙烷在催化剂表面的吸附状态和吸附强度以及催化剂性能的影响.结果表明,Sn/Nb摩尔比明显影响催化剂的组成和结构;催化剂的结构不同,环氧乙烷在催化剂表面的吸附强度存在明显差别,催化剂的催化性能明显不同.     

煅烧温度对Li4Ti5O12的电化学性能的影响

用溶胶-凝胶法制备了尖晶石型锂钛复合氧化物L i4Ti5O12,并研究了煅烧温度对其电化学性能的影响。结果表明,在800℃煅烧12 h得L i4Ti5O12,晶型良好,粒度较均匀。并且表现出良好的电化学性能,循环10次后比容量仍保持在160 mAh.g-1左右。     

Thermal study of CoxZn7-xSb2O12 spinel obtained by pechini method using different alcohols

With the aim of obtaining materials with applications in pigments, Co_xZn_7-xSb₂O₁₂ spinels were synthesized using the Pechini method. This method consists in the formation of a polymeric net, where the metallic cations are homogeneously distributed. In this work, two types of alcohol (ethyl glycol and ethylene glycol) were used for the synthesis of a zinc antimoniate spinel, Co_xZn_7-xSb₂O₁₂ (x=0-7). The materials were characterized by termogravimetry (TG) and differential thermal analysis (DTA). TG results indicated a decrease in total mass loss when cobalt was added to the solution substituting zinc, for samples prepared using the two different alcohols. Decomposition temperatures, obtained by TG and DTA, presented a decreasing behavior as cobalt was added to the material. In relation to the alcohols, all results indicated a better polymerization of the resin when ethylene glycol was used, being the most indicated one for cation immobilization. X-ray diffraction did not show differences between the two alcohols - both presented the spinel phase (Co, Zn)_2.33Sb₀.₆₇O₄. Samples with higher quantity of cobalt also presented ilmenite phase (Co, Zn)Sb₂O₆. This revised version was published online in August 2006 with corrections to the Cover Date.     

负载型无铬超细铁基变换催化剂的制备和催化性能

 以镁铝尖晶石为载体，以过渡金属氧化物为助剂，用吸附γ－Fe2O3胶体法制备了负载型无铬铁基变换催化剂．TEM，XRD，BET和活性测试结果表明，采用胶体负载法制备的变换催化剂，其活性组分Fe3O4以分立的超细微颗粒分布在镁铝尖晶石载体表面上，颗粒之间存在一定的间隔．过渡金属氧化物NiO或V2O5能够进入Fe3O4晶格形成固溶体，起到代替氧化铬的作用，提高催化活性．负载型催化剂FeNi／MgAl2O4（m（NiO）／m（Fe2O3）＝3％）在汽／气比为1和空速为2000h－1的反应条件下，CO转化率在400和350℃时分别为95％和80％；在高空速和低汽／气比条件下也具有很好的催化性能．稳定性实验结果表明，该催化剂 具有良好的热稳定性和一定的抗硫能力．与非负载型催化剂相比，负载型催化剂具有更为优越的催化性能．     

载体对负载型TiO2催化剂光催化性能的影响

 以活性碳（AC）和镁铝尖晶石（MA）为载体，采用真空吸附水解法制备了负载型光催化剂TiO2／AC和TiO2／MA，并采用TiO2溶胶负载法制备了活性碳负载催化剂TiO2（C）／AC．以氯仿为探针分子研究了其在催化剂上的吸附及光催化降解反应性能．结果表明，催化剂的制备方法、TiO2负载量与载体的吸附性能对光催化活性有明显的影响．通过优化制备条件，TiO2／AC催化剂的催化活性可提高到纳米TiO2的2．5倍．氯仿在AC上的饱和吸附量较高，但吸附强度较弱；在纳米TiO2上的吸附情况则正好相反．氯仿在AC和TiO2上吸附性质的差异有利于吸附在TiO2／AC上的氯仿分子从活性碳载体向TiO2光催化活性中心迁移．镁铝尖晶石载体对光催化反应没有明显的促进作用，与其基本上不吸附氯仿分子有关．与TiO2胶体负载法相比，真空吸附水解法是一种较好的负载型TiO2光催化剂制备方法．     

Comparative study on the synthesis, photoluminescence and application in InGaN-based light-emitting diodes of TAG:Ce phosphors

Cerium-doped terbium aluminum garnet phosphors, Tb₃Al₅O₁₂:Ce³⁺ (TAG:Ce³⁺), were prepared with different methods: co-precipitation (CP), half dry-half wet (HDHW), sol-combustion (SC) and Pechini method plus conventional solid state reaction (SS) method. Comparative study on the phase-formation, particle size, morphologies and luminescent characteristics of the phosphors synthesized with different methods was carried out by means of XRD, FE-SEM and photoluminescence (PL) analysis and SC method was confirmed by the comparison of the results to be an easy and an effective process for preparing efficient and nano-sized Tb₃Al₅O₁₂:Ce³⁺ phosphors. Various factors influencing particle size, morphology and PL of the phosphors, such as precursor preparation, reaction temperature and heating time, were also investigated. Light-emitting diodes (LEDs) were fabricated with each phosphor and a ∼460 nm emitting InGaN chip. The LEDs from SS, HDHW and CP exhibit strong white emission while those from SC and Pechini emit yellow, revealing that the emission characteristics of LEDs are influenced not only by the morphology and the particle size of the phosphors, but also by the preparing process of the phosphors.     

LiMg0.5Mn1.5O4的合成及对Li+的离子交换选择性

锂及其化合物在航空航天、化工、医药、空调、高能电池和热核反应等方面都有广泛应用，对锂及其化合物的需求与日俱增。我国液体锂资源非常丰富，开发利用其中的锂资源具有重要意义。从盐湖水、地下卤水、盐田母液、油气田水等咸水资源中提取锂的方法有碳酸盐沉淀法、离子交换法、萃取法等。离子